0 20 40 60 80 100 trim fix on off 360° Complete reset replace foil + cutter Type 5647 550 4 English 10 Braun GmbH Frankfurter Straße 145 61476 Kronberg / Germany 5-647-321/00/IV-07 China/GB 13 4 8 trim fix on 0 20 40 60 80 100 off reset replace foil+ cutter 6 5 4 3 2 1 9 10 11 12 7 4 8975 fix on fix on 0...20 40 60 80 100 0...20 40 60 80 100 0...20 40 6 trim fix on reset foil repl foil replace+cutt foil replace+cutte 5 6 fix on off oil on off 0...20 40 60 80 fix on off et foil replace+ 7 8 9 English Our products are designed to meet the highest standards of quality, functionality and design. We hope you enjoy your new Gillette shaver powered by Braun. The system tells you when to replace the shaving foil and cutter block. Warning Keep the appliance dry. Your shaver is provided with a special cord set with integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it. Otherwise there is a risk of electric shock. 8975 Description 1 2 3 4 5 6 7 8 9 10 11 12 13 Foil protection cap Shaver foil Cutter block Release buttons Long hair trimmer Switch Charging lights (green) Low charge light (red) Replacement light for shaving parts Reset button Pilot light Shaver socket Special cord set Charging the shaver · When charging for the first time: Using the special cord set, connect the shaver to an electrical outlet. The shaver must be switched off. Charge it for at least 4 hours (special cord set and shaver might get warm). Once the shaver is completely charged, shave until fully discharged. Then recharge to full capacity again (1 hour). · A full charge will give up to 50 minutes of cordless shaving time, depending on your beard growth. However, the maximum battery capacity will only be reached after several charging/discharging cycles. · Best environmental temperature range for charging is from 15 °C to 35 °C. · When fully discharged, you may also shave with the shaver connected to an electrical outlet via the special cord set. 10 Indicator lights Pilot light (11): The shaver is connected to an electrical outlet. 0...20 40 6 reset foil repl Shaving Switch positions off = (switch is locked) Press and push up the switch to operate the shaver: on = Shaving with the pivoting head (the pivoting cutting system automatically adjusts to every contour of your face). fix = Shaving with the pivoting head locked at an angle (to permit shaving in difficult areas, e.g. under the nose). trim = The long hair trimmer is activated (for trimming sideburns, moustache and beard). on fix on fix on 0...20 40 trim fix foil replace+cutt The red low charge light (8) flashes when the battery capacity has dropped below 20%, provided the shaver is switched on. The remaining capacity will then be sufficient for 2 to 3 shaves. 60 80 100 0...20 40 Model 550: When the shaver is fully charged, all five charging lights (7) will light up (20% per light), provided the shaver is connected to an electrical outlet or switched on. foil replace+cutte 60 80 100 11 Tips for the perfect shave · We recommend that you shave before washing, as the skin tends to be slightly swollen after washing. · Hold the shaver at right angles (90°) to the skin. Stretch your skin and shave against the direction of beard growth. · To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light (9) comes on (after about 18 months), or when worn. Cleaning Never use water to clean the shaver. For easy cleaning after each shave, switch the shaver off. Press the release buttons to lift the shaver foil (do not remove the foil completely). Switch on the shaver for approx. 5­10 seconds so that the shaved stubbles can fall out. Then remove the shaver foil and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the shaver foil nor the cutter block with the brush as this may damage them. on off fix on off Keeping your shaver in top shape oil off off About every four weeks, clean the cutter block with Braun cleaning agents. Put a drop of light machine oil onto the long hair trimmer and the shaver foil. Replacement light for shaving parts / Reset To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light for shaving parts (9) comes on (after about 18 months) or when worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil and cutter block: 51S) The replacement light will remind you during the next 7 shaves to replace the shaving parts. Then the shaver will automatically reset the display. fix fix on on 0...20 40 12 et foil replace+ 60 80 After you have replaced the shaving parts (foil and cutter block), use a ball-pen to push the reset button (10) for at least 3 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. The manual reset can be done at any time. Preserving the batteries In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (through normal use) every 6 months approximately. Then recharge the shaver to full capacity. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time. Environmental notice This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country. Subject to change without notice. This product conforms to the European Directives EMC 89/336/EEC and Low Voltage 2006/95/EC. For electric specifications, see printing on the special cord set. 13 ...