GS-105B/108B Gigabit Switch User's Guide Version 1.00 Edition 1 1/2008 Table of Contents ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO SVENSKA 2 14 20 26 32 38 44 Copyright © 2008. All rights reserved. ENGLISH 1 Introduction The switch is a multi-port switch that can be used to build high-performance switched networks. The switch is a store-and-forward device that offers low latency for highspeed networking. The switch is designed for SOHO (Small Office Home Office) businesses. The switch can be used as a standalone switch to which computers, servers and print server are directly connected to form a small workgroup. 2 Hardware Installation The switch is suitable for an office environment where it can be placed on a desktop. 1 Make sure the switch is clean and dry. 2 Set the switch on a smooth, level flat space strong enough to support the weight of the switch and the connected cables. Make sure there is a power outlet nearby. 3 Use only the supplied power adaptor to connect your switch to a power source. Refer to the label on the power adapter for more information. 2 ENGLISH Do not block the ventilation holes. 3 Hardware Connection The power and the Ethernet ports are located on the rear panel. 3.1 Power Connection Connect one end of the supplied power adaptor to the power port on the rear panel of the switch and the other end to the appropriate power source. The PWR LED turns on. 3 ENGLISH 3.2 RJ-45 Auto-negotiating Ports The switch comes with 5 or 8 10/100/1000M RJ-45 ports depending on the model of your switch. The autonegotiation feature allows the switch to detect the speed of incoming transmission and adjust appropriately without manual intervention. It allows data transfers of 10 Mbps, 100 Mbps or 1000 Mbps in either half-duplex or fullduplex mode depending on your Ethernet network. 3.3 Auto-crossover Ethernet Ports All ports are auto-crossover, that is auto-MDIX ports (Media Dependent Interface Crossover), so you may use either a straight-through Ethernet cable or crossover Ethernet cable for all Ethernet port connections. Autocrossover ports automatically sense whether they need to function as crossover or straight ports, so crossover cables can connect both computers and switches/hubs. Refer to the Product Specifications section for the types of network cable used for the different connection speeds. 4 ENGLISH 3.4 Front Panel LEDs The LEDs on the front panel indicate the real-time status of the switch. LED PWR COLOR Green STATUS DESCRIPTION On Off The switch is on and receiving power. The switch is not receiving power. The port is connected to an Ethernet network. The port is receiving or transmitting data. The port is not connected to an Ethernet network. LNK/ ACT Green On Blinking Off 5 ENGLISH 4 Product Specification Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE802.3x Full Duplex Operation and Flow Control CSMA/CD Store-and-Forward switching architecture 14,880 pps for 10Mbps 148,800 pps for 100Mbps 488,000 pps for 1000Mbps 5/8 Gigabit Copper: RJ-45 Auto-MDIX on all ports GS-105B: 1K MAC address table GS-108B: 8K MAC address table GS-105B: 104K byte GS-108B: 144K byte 10BASE-T: 100W 2-pair UTP/STP Cat. 3, 4, 5 100BASE-TX: 100W 2-pair UTP/STP Cat. 5 Gigabit Copper: 100W 4-pair UTP/STP Cat. 5 GS-105B: 10Gbps GS-108B: 16Gbps Per port: LNK/ACT Per unit: PWR GS-105B: External power DC 5V/1A GS-108B: External power DC 12V/1A Protocol Technology Transfer Rate Connector MAC Address Memory Buffer Network Cable (Up to 100m or 328ft) Backplane LED Power Supply 6 ENGLISH Power Consumption Operation Temperature Operation Humidity Dimension EMI & Safety GS-105B: 3.7 Watt (maximum) GS-108B: 6.12 Watt (maximum) 0º C to 40º C (32º F to 104º F) 10% to 90% (Non-condensing) GS-105B: 121 x 75 x 26 mm (L x W x H) GS-108B: 154.5 x 85 x 26 mm (L x W x H) FCC Class A, CE Certifications Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: · This device may not cause harmful interference. · This device must accept any interference received, including interference that may cause undesired operations. 7 ENGLISH FCC Warning This device has been tested and found to comply with the limits for a Class A digital switch, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This Class A digital apparatus complies with Canadian ICES-003. 8 ENGLISH Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning: Viewing Certifications Refer to the product page at www.zyxel.com. Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. · Do NOT use this product near water, for example, in a wet basement or near a swimming pool. · Do NOT expose your device to dampness, dust or corrosive liquids. 9 ENGLISH · Do NOT store things on the device. · Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. · Connect ONLY suitable accessories to the device. · Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. · Make sure to connect the cables to the correct ports. · Place connecting cables carefully so that no one will step on them or stumble over them. · Always disconnect all cables from this device before servicing or disassembling. · Use ONLY an appropriate power adaptor or cord for your device. · Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). · Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. · Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. · If the power adaptor or cord is damaged, remove it from the power outlet. 10 ENGLISH · Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. · Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. · Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. · If you wall mount your device, make sure that no electrical lines, gas or water pipes will be damaged. This product is recyclable. Dispose of it properly. 11 ENGLISH Warranty ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. 12 ENGLISH Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser. To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country. 13 DEUTSCH DEUTSCH 1 Einleitung Der Switch ist ein Multiport-Switch, der zum Aufbau geschalteter Hochleistungsnetzwerke eingesetzt werden kann. Der Switch ist ein Teilstrecken-Gerät (,,Store and forward") der geringe Latenz für Hochgeschwindigkeitsnetzwerkanwendungen bietet. Der Switch wurde für SOHO-Anwendungen (kleine Büro- und Heimanwendungen) entwickelt. Der Switch kann als selbständiger Switch eingesetzt werden, an den Computer, Server und Druckserver zur Bildung einer kleinen Arbeitsgruppe direkt angeschlossen werden. 2 Hardware-Installation Der Switch eignet sich für Büroumgebungen und kann auf einem Schreibtisch platziert werden. 1 Vergewissern Sie sich, dass der Switch sauber und trocken ist. 2 Setzen Sie den Switch auf eine glatte, waagerechte Oberfläche, die stabil genug ist, den Switch und die angeschlossenen Kabel zu tragen. Vergewissern Sie sich, dass sich eine Steckdose in der Nähe befindet. 3 Verwenden Sie nur das mitgelieferte Netzteil, um Ihren Switch mit einer Stromquelle zu verbinden. Das Typenschild des Netzteils bietet Ihnen weitere Informationen. 14 DEUTSCH Blockieren Sie nicht die Belüftungsöffnungen. 3 Hardware-Anschluss Die Stromversorgungs- und Ethernet-Anschlüsse befinden sich auf der Rückseite. 3.1 Stromanschluss Verbinden Sie ein Ende des mitgelieferten Netzteils mit dem Stromanschluss auf der Rückseite des Switches, das andere Ende mit einer geeigneten Stromquelle. Die PWR-LED leuchtet auf. 15 DEUTSCH 3.2 RJ-45 Auto-negotiating-Ports Der Switch wird mit 5 oder 8 10/100/1000M RJ45-Ports geliefert, je nach Modell Ihres Switchs. Die Autonegotiation-Funktion ermöglicht dem Switch, die Geschwindigkeit ankommender Übertragungen zu erkennen und sich ohne manuellen Eingriff darauf einzustellen. Sie erlaubt Datenübertragung mit 10 Mbps, 100 Mbps oder 1000 Mbps im Halb- oder Vollduplexmodus, abhängig von Ihrem EthernetNetzwerk. 3.3 Auto-crossover-Ethernetports Sämtliche Ports sind als Auto-crossover-Ports , nämlich als Auto-MDIX-Ports (Media Dependent Interface Crossover) ausgelegt - also können Sie entweder durchkontaktierte oder gekreuzte (Crossover) Ethernetkabel für alle Ethernetportverbindungen benutzen. Auto-crossover-Ports erkennen automatisch, ob sie als Crossover- oder als Direkt-Ports arbeiten müssen, daher können Sie Crossover-Kabel sowohl zum Anschluss von Computern als auch zum Anschluss von Switches / Hubs verwenden. Eine Übersicht über die für verschiedene Verbindungsgeschwindigkeiten einsetzbaren Kabeltypen finden Sie im Abschnitt Produktspezifikationen. 16 DEUTSCH 4 Frontplatten-LEDs Die LEDs an der Frontplatte zeigen den Echtzeit-Staus des Switchs an. LED PWR FARBE Grün LNK/ ACT Grün STATUS BESCHREIBUNG An Der Switch ist eingeschaltet und wird mit Strom versorgt. Aus Der Switch wird nicht mit Strom versorgt. An Der Port ist mit einem EthernetNetzwerk verbunden. Blinken Der Port empfängt oder sendet Daten. Aus Der Port ist nicht mit einem EthernetNetzwerk verbunden. 17 DEUTSCH 5 Produktspezifikationen Standard IEEE 802.3 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE802.3x mit Vollduplexbetrieb und Flusskontrolle CSMA/CD Store-and-Forward switching-Architektur 14.880 pps bei 10 Mbps 148.800 pps bei 100 Mbps 1.488.000 pps bei 1000 Mbps 5/8 Gigabit-Kupfer: RJ-45 ; Auto-MDIX an allen Ports GS-105B: 1K Mac-Adresstabelle GS-108B: 8K Mac-Adresstabelle GS-105B: 104 KB GS-108B: 144 KB 10B ...